Search results

Tortoise shell 9 hole pick guard and strat black knob and switch tip if possible. Thank you

I am trying to like them.. I’d prefer keeping this strat stock.. I’m playing around with pup height and may put back the original trem.. I switched that out for a Wudtone trem with steel block.. someone mentioned to me that even though the original one piece zinc trem is no very well liked by...

I might try and swap the whole harness and pups.. I do have a set of TeMex pups.. I like them much better than the Texas Specials..

Not sure I’m getting along with my 81 pups.. (X1 in bridge) ... I don’t know what is normal expectations tone wise on these.. ? They are kind of bright and squeaky.. not spikey.. maybe a tad bit microphonic .. Maybe better to my ears on the clean channels of my amps vs. gain or high gain...

Thanks! Haven’t bought it yet. I mainly use graphtec for all my nuts.. It’s for my 81 strat and they don’t have a curved nut either the width and string spacing I need.. but they have a flat strat nut that is much closer to the spacing and width.. I have no problem sanding down the base of the...

Pre-slotted Graphtec nut.... Can I use a flat nut on a radius nut slot if I sand the bottom of the nut to match the radius of the nut slot?

Doh!!!! Pics! Here is a couple from the seller.. I’ll post a couple more when I’m back in my studio.. Yes.. very nice guitar..

Wow.. just picked up a used Yamaha 620 Revstar.. Very very nice guitar.. feels very Gibson like.. well made.. stock pups sound good.. what a nice electric and good pricing..

For me .. out of. My champ, Orange micro terror, Marshall Class 5, orange 120c which is big but sounds great at lower volumes.. My Yamaha THR10c is the best low volume amp I have.. it still amazes me how much this thing even feels.. the interaction between guitar and amp is there.. excepts...

Just got a used HT-5 MKii head.. I have tried it through a Mesa boogie 1x12 cab, a closed back 1x12 cab with brown label fender speaker, a custom cab with a 1x10 and 1x12 Jensen mod speakers, a Zinky 2x12 closed back cab.. Tried it with a bunch of strats .. some with custom wiring mods, SG...

I would like to get the Gotoh NS510TS-FE2 - 2-7/32" Mounting / 2-1/16" String Spacing - Steel Block - Highwood & Block Saddles - $70.00 Shipped please. Could you send your PayPal link or info.. Thank you!

I went over the bridge plate and the body.. both are drilled bad.. the bottom 3 holes skew away from the neck and the holes on the bridge plate same.. so the both together exaggerate the situation.. I installed a properly machined bridge and the exaggerated skew was improved.

Thanks!! Glad you got that!

I ordered it with a white pg brand new. I’m the og owner and that is the og pg. 1981. The screw holes are definitely out of alignment. I won’t touch it if I can set it up properly, have the trem wok right and most importantly can intonate. When I screw the e a d screws in the bridge stays...

Thanks for the reply.. I agree.. I removed the bridge and g b e screw holes are misaligned. So I’ll set all up as is and if it works as it should and can intonate I’ll leave it.. if not, re drill those 3 holes.

I ordered it that way.. all original.

I don’t think that’s it in this case.. for a couple reasons..

Good eye , I see that now... maybe it is the plate. I hope it is. I’ll look into that .

The bridge is angle back on the high E so it’s not about the spring it’s that the high e saddle needs to be moved forward towards the screw.. to compensate..

I just got my 1st guitar back after being separated for 30 years. I have learned so much about strats and guitars since then. So I am noticing that the 6 screw holes for the bridge seem off? Don’t think it’s the Pickguard... You can see from the back of the block.. and how forward the...

I can replace was just wandering if the 1979 year nut slot was flat or radius I know all the fender mim nut slots i have dealt with were radius.

I know this is a old thread but wanted to know if the nut slot on your 79 strat was flat or radiused?

Awesome! Do you have link or any info to order the Schallers? So you can ge the Schallers.. and the og covers fit? and they drop right in? cool..

Thanks! I have Highwood saddles on the Pure vintage bridge that I plan installing.. I have always been more of a fan of the modern block saddles .. I like the notch in the Highwoods and the way the grub screws attach.

Dont plan on changing electronics but if I do I will keep the original as is and replace with a complete new harness and store the original.